Products
Industrial Wood Pellet Production Line for Poultry Bedding
Industrial Wood Pellet Production Line for Poultry Bedding: Sizing a Cedar Line From 1,000 m3 a Year
Features
Quick answer
An industrial wood pellet production line for poultry bedding is sized from the litter backwards, not from a press catalogue. At the 18% moisture density given for Cryptomeria, 1,000 m3/year x 380 kg/m3 = 380 t/year, which is 1.27 t/day over 300 working days or 1.52 t/day over 250, and only 0.16 to 0.19 t/h across an eight hour day. A 55 kW flat die frame rated 500-800 kg/h carries that duty in a 2 to 3 hour shift with less derating and lower specific energy than a ring die frame, and the line from the planer outlet totals about 92 kW connected, Illustrative.
▪
Bedding grade is specified on absorbency, dust and softness; fuel grade on calorific value, ash and durability.
▪
1,000 m3 a year at 380 kg/m3 is 380 t a year, 1.27 t/day at 300 days and 1.52 t/day at 250 days.
▪
The planer is not in our catalogue; the existing DURA YT 145 stays and our scope starts at its outlet.
▪
Diameter takes the small side of the die range, hardness is set by compression ratio, and no bedding standard exists to certify against.
▪
Connected power is about 92 kW on the flat die frame and about 127 kW on the ring die frame, both Illustrative.
Poultry bedding is bought for what it takes up, not for what it gives off. That difference reorders every decision on the line: the die is chosen for a soft pellet rather than a dense one, the dryer is sized on absorbency rather than calorific value, and the tonnage is set by litter changes in a house rather than by a furnace. This page carries one measured starting point, 1,000 m3 of Cryptomeria a year on Reunion, through density, daily output, the existing planer, grinding, drying, pressing, cooling and bagging to the power total and the terms of a proposal.
1.5-2 t/h Ring die biomass pellet making machine testing
I am interested in this production
01
How Do Bedding Pellets Differ From Fuel Grade in Specification?
Poultry litter is judged by absorption and a fuel pellet by combustion. That one sentence separates the two specifications and moves the die, the compression ratio, the dryer duty and the bag: a fuel pellet must be dense and hard, while a bedding pellet has to wet through, break down under foot and release little dust.
Criterion
Bedding grade
Fuel grade
Who fixes the value
Diameter
Small side of the die range, 4-6 mm
6-10 mm for most furnace feeds
Litter trial against boiler feeder
Hardness
Low compression ratio, breaks down when wetted
High, survives conveying and a tumbler test
Poultry house
Absorbency
The primary property, measured by soak and drain
Not measured
Poultry house
Dust at bag opening
Kept low, screened before bagging
Kept low for the burner intake
Poultry house
Calorific value
Not a specification
GCV and NCV head the grade sheet
Boiler or fuel buyer
Ash content
Not a specification
A grade field
Boiler or fuel buyer
Bulk density
Not a target
Tied to energy per cubic metre
Logistics
Published standard
None applies; fields held to confirmation
Grade sheets exist in the trade
Contract
Absorbency, dust fraction, hardness and durability are all to be confirmed against the factory technical confirmation sheet, and the values that mean anything are measured in the buyer's own house.
How to judge a bedding pellet against a fuel pellet
Three bench tests need no laboratory. Absorbency: weigh 200 g, immerse 10 minutes, drain 2 minutes, weigh again and state the gain as a percentage of starting mass. Dust: sieve 1 kg over a 2 mm screen. Hardness: drop 500 g from 1 m onto concrete and count what stays whole.
Absorbency, dust and hardness bands
The three properties trade against each other, and the trade is set at the die. A higher compression ratio, die wall thickness over hole diameter, gives a harder pellet: fewer fines in the bag, less dust in the house, slower wicking once wetted.
For a light material a low ratio is not a compromise. Cedar at 330-380 kg/m3 dry needs little compression to hold in a 15 kg bag, so the die can favour absorption and still turn out a pellet that arrives intact. That is the opposite of the fuel case, and the reason a bedding die and a fuel die are two dies even on one frame.
02
How Does 1,000 m3 Per Year Convert Into a Daily Output?
The conversion runs one way and has one weak link, the density figure at the front of it. On the 18% moisture basis supplied in the enquiry, 1,000 m3/year x 380 kg/m3 = 380 t/year. Divided by 300 working days that is 1.27 t/day; divided by 250 working days it is 1.52 t/day. Across an eight hour day the rate is 0.16 to 0.19 t/h, while the same tonnage inside a 3 hour shift leaves the press at 0.42 to 0.51 t/h.
Reference
cedar species naming and density differences explains why a density figure has to name the species before it is used in a conversion.Next step
share cedar volume, moisture and bag size for bedding and the conversion is re-run on your own figures.
The decision rule for annual volume to daily output
Fix three inputs, then divide: the annual volume from the forestry side, the density from the moisture basis in the purchase contract, and the working-day count from the poultry house cycle. Only the density is settled the moment the wood is bought by volume or by weight, and moving it afterwards shifts the required output by more than half.
250 to 300 working days
A six day week gives about 300 working days and a five day week about 250, and the 20% difference in days is a 20% difference in daily tonnage: 1.27 t/day against 1.52 t/day. One warning belongs here: 0.16 to 0.19 t/h is a working-day average, and no press is sized on an average.
03
Why Does Cedar Density Change the Tonnage Per Cubic Metre?
A cubic metre of wood is mostly air and water, and only part of it is fibre. Applied density moves by nearly a factor of two between oven-dry material and a freshly felled log, and every tonne in the quotation derives from that figure.
Reference
Sugi (Cryptomeria japonica) wood density data gives the species figures behind the density bands used on this page.Measurement basis
Density
What 1,000 m3 weighs
Per day at 300 days
Per day at 250 days
Dry cedar
330-380 kg/m3
330-380 t
1.10-1.27 t
1.32-1.52 t
At 18% moisture, contract basis
380 kg/m3
380 t
1.27 t
1.52 t
Fresh cedar
500-650 kg/m3
500-650 t
1.67-2.17 t
2.00-2.60 t
Read the bottom row and the same 1,000 m3 becomes 500-650 t a year, 1.3 to 1.7 times the middle row. Nothing about the forest changed; only the water did.
Density band dry, at 18% moisture, and fresh
The 330-380 kg/m3 band belongs to dried material, where the press works with fibre and little water. The 380 kg/m3 at 18% is the working basis here: dry enough to store, wet enough that a dryer stays in scope. The 500-650 band belongs to freshly felled material, where free water fills the cell cavities.
Those bands drive different machines. On the dry basis the dryer may drop out. At 18% it stays at the small end. On fresh material it becomes the largest heat load on site and the crusher works harder, because wet slabs are tougher under the hammer.
How to judge a wet purchase
Weigh three samples from three deliveries, oven-dry each, and compute density at the moisture the line will see. A stack of slabs carries more void space per tonne than round logs, so volume and weight diverge most on the cheap half of the intake.
04
Which Grinding and Drying Steps Follow the Planer Stage?
Grinding is the cheap station and drying is the expensive one, and the two are sized from opposite ends. The crusher follows the planer outlet and the press appetite; the dryer follows the water that has to leave, which is why its rating tracks the density basis rather than the tonnage.
Related
the wood pulveriser after the planer shows the reduction stage on its own.The smallest crusher frame is rated 7.5 kW at 600-1000 kg/h, and the hammer family runs from 1.5 kW at 60-120 kg/h to 45 kW at 1000-2000 kg/h. At 0.42 to 0.51 t/h the smallest frame runs at 42 to 85 percent of its 600-1000 kg/h band, so the headroom is close to a factor of two at the top.
Grinding and drying capacity band
Drying is quoted from three families. A single shell drum of 0.8 x 8 m draws 4.0 kW on the drive and 7.5 kW on the fan; an airflow unit of the 219 type draws 4 kW in 7.5 x 1.5 x 3 m; a vertical batch unit runs 50 to 400 kg per batch on 5 to 22 kW of heating. The rotary family carries an inlet band of 10% to 80% and an outlet of 15%.
The press inlet window for cedar shavings is ; the 12%-20% printed for the feed ring die range belongs to feed milling and does not transfer to wood.
The decision rule for dryer type
Count the hours the line runs per day. Below about 2 hours a batch vertical unit fits, since a 400 kg batch every 30 to 40 minutes covers 0.6 to 0.8 t/h. Above about 4 hours the continuous drum is the fit. At 2 to 3 hours the deciding factor is incoming moisture, and on fresh material the water load doubles.
05
Which Press Frame Matches 1.3 to 1.5 Tonnes Per Day of Bedding?
At 1.27 to 1.52 t/day over a 2 to 3 hour shift the press works at 0.42 to 0.76 t/h, and that band rules out most of the catalogue in both directions. Frames below 300 kg/h cannot hold a 2 hour shift; frames above 1.5 t/h are paid for and never reached.
Related
the pellet machine options for bedding set the flat die and ring die families side by side.

Model
Rated capacity
Power
Pellet size
Weight
Overall size
Role for this duty
RKL-250
100-200 kg/h
15 kW
4-6 mm
0.5 t
1400 x 600 x 1000 mm
Below the shift rate
RKL-300
150-250 kg/h
22 kW
4-6 mm
0.65 t
1780 x 670 x 1000 mm
Below the shift rate
RKL-350
100-300 kg/h
30 kW
4-8 mm
0.76 t
1860 x 670 x 1600 mm
Below the shift rate
RKL-400
300-600 kg/h
37 kW
4.5-10 mm
2.2 t
1900 x 850 x 1750 mm
Covers 3 hours, no headroom at 2
RKL-450
500-800 kg/h
55 kW
4.5-10 mm
4.3 t
2300 x 1100 x 1900 mm
Recommended frame
RKL-550
1000-1500 kg/h
90 kW
4.5-12 mm
5.5 t
2350 x 1100 x 2050 mm
Paid for, never reached
MKLH560
1-1.5 t/h
90 kW
4-12 mm
5.2 t
2620 x 1640 x 1770 mm
Expansion and fuel grade option
MKLH560A
1.5-2 t/h
132 kW
4-12 mm
5.6 t
2680 x 1560 x 1770 mm
Beyond this volume
MKLH700
2-2.5 t/h
160 kW
4-12 mm
7.2 t
2560 x 1380 x 2020 mm
Beyond this volume
MKLH860A
3-4 t/h
250 kW
4-12 mm
9.5 t
3150 x 1550 x 2240 mm
Beyond this volume
The decision rule for a frame by shift hours
Three questions, in this order. How many hours a day will the line run: at 2 hours the shift rate reaches 0.76 t/h and a 600 kg/h upper limit is too tight, at 3 hours it falls to 0.51 t/h and a 500 kg/h lower limit leaves margin. Second, will the mill still be making bedding in five years, or selling fuel pellets. Third, is there a poultry house on the same site that takes the output.
1-1.5 t/h against 500-800 kg/h
A 3 hour shift at 1.52 t/day asks for 0.51 t/h, near the floor of that band, and near the floor is where specific energy is best: 55 kW rather than 90 kW for the same output, a smaller die set, and 4.3 t of frame on the slab.
The ring die frame rated 1-1.5 t/h on 90 kW is a genuine second option. It takes the same 0.51 t/h at 34% to 51% of its band, so it is heavily derated. What it buys is headroom: a second poultry house, or fuel pellets at 6 to 8 mm, ride on the same frame at 1 to 1.5 t/h.
That is a recommendation, not the only answer. A mill that expects to trade within three years should take the ring die frame and accept the derating; a farm bedding its own houses should take the flat die frame.
06
What Pellet Diameter and Hardness Suit Poultry Bedding Use?
Diameter and hardness are two separate decisions, and bedding takes both towards the soft end. The die range covers 4 to 12 mm on both families, so neither is a machine constraint; the choice is a die order.
For litter the small side is the right side. A 4-6 mm pellet spreads more evenly from a scoop, wets through faster because the wetted surface per unit mass is larger, and does not roll away from the drinker line the way a 10 mm fuel pellet does.
How to judge pellet hardness for litter
Hardness is set at the die by compression ratio and cannot be adjusted at the panel. The target is a pellet that survives the bag and opens up within minutes of being wetted.
Two tests, both on a bag from the trial run. Drop 500 g from 1 m onto concrete and count what stays whole: a bedding pellet should show some breakage, because one that never breaks will not absorb. Then immerse 200 g for 10 minutes and watch it soften and disintegrate. Durability and dust fraction stay to be confirmed, since no bedding standard exists to test against.
Diameter band 4-12 mm
A 4 mm die and a 6 mm die cost the same to cut and fit the same frame, so order both, run a week on each, and let the poultry house decide. Output falls as hole diameter falls, so the 4 mm die is the conservative one for a capacity commitment, and a fuel specification should not be carried over to litter.

07
Which Cooling, Sieving and Bagging Units Close the Bedding Line?
The closing stations are small in power and large in effect on the product. A warm pellet bagged straight off the die sweats and cakes in storage. The order is cooling, then sieving, then bagging.
Related
the line running video shows the cooling, sieving and bagging stations in sequence on a comparable line.Cooling is covered by a counterflow unit rated 300-500 kg/h at 4.4 kW on the fans and 0.75 kW on the discharge. Sieving is covered by a cooling and sieving unit rated 800-1000 kg/h at 8 kW. Bagging is a 3 kW automatic weighing scale covering 10-50 kg at 260-300 bags/h, with automatic weighing, a conveyor, a sewing head and computer control, at +/-0.1% static and +/-0.2% dynamic accuracy.
Cooling and sieving capacity band
The cooler is the one row where a 2 hour shift does not fit. At 0.76 t/h the 300-500 kg/h band is exceeded, and the next size up, rated 1000-3000 kg/h at 5.5 + 2.1 kW, adds 2.45 kW to the total. Laying the plant out on 3 hours a day keeps the smaller cooler valid.
The decision rule for bag size
Bag size follows the hand that carries it. A 15 kg bag is the manual handling norm, a 25 kg bag suits a spreader or a loader, and a 10 kg bag suits a small holder buying by the pallet. All three sit inside the 10-50 kg weighing range, so the bag is a setting rather than a machine.
A sewn 15 kg woven bag is the normal farm pack, and a heat seal has to be matched to the bag film first.
08
What Per Machine Configuration and Connected Power Total Result?
The station list below is the complete scope from the planer outlet to the bag, one row per station. The press row carries both options, because the frame choice is the only decision that moves the total by a large amount.
Step
Equipment
Model segment
Power
Rated capacity
Grinding
Wood chip crusher
MK-420
7.5 kW
600-1000 kg/h
Drying
Single shell rotary dryer, 0.8 x 8 m
0.8 x 8
4.0 + 7.5 kW
Moisture dependent, to be confirmed
Pelleting
Flat die press
RKL-450
55 kW
500-800 kg/h
Pelleting, alternative
Ring die press
MKLH560
90 kW
1-1.5 t/h
Cooling
Counterflow cooler
GMC-LQSF70
4.4 + 0.75 kW
300-500 kg/h
Sieving
Cooling and sieving unit
LX-LS50
8 kW
800-1000 kg/h
Bagging
Automatic weighing and sewing scale
DCS-Z-W-50
3 kW
260-300 bags/h, 10-50 kg
Conveying
Screw feeder
KWX50YP
1.5 kW
0-1000 kg/h

Connected load by station
Both are sums of motor nameplate ratings and both are . Pelleting is 60% of the flat die total and 71% of the ring die total, and everything downstream of the press adds 17.65 kW, which is why the closing machines rarely force a supply upgrade.
Two exclusions: dust collection fans, compressed air for the bagger at 0.6-0.8 MPa and 0.2 Nm3/min, and lighting all sit outside both totals, and the transformer is sized on the total plus the starting current of the largest motor.
The decision rule for summing stations
Add the rows, then compare the result only against a total built the same way. The retrofit scope described elsewhere on this site sums to roughly 102 to 124.5 kW for four replacement machines, and the two figures are not comparable: that sum carries a 7.5 to 30 kW pulveriser and no dryer, while this one carries a 7.5 kW crusher and an 11.5 kW dryer.
Automation sits on the same sheet. The bagging scale is the automated section, with automatic weighing, a conveyor, a sewing head and computer control. The press carries a forced feeder and a local panel holding die speed and feed rate. ; interlock signals between press, cooler and bagger are agreed per project.
9
Why Does a 1.5 Tonne Per Day Bedding Line Make Economic Sense?
Because the alternative is buying litter in, and the comparison is a bag against a bag rather than a tonne against a boiler. A line at this size does not compete with industrial pellet plants; it competes with the delivered price of the bedding a poultry house already uses.
Related
the small biomass pellet line reference build shows a plant of this scale laid out on one floor.Volume is the first check. A line of 1.5 tonnes per day over 25 working days a month is 37.5 t/month, which at 15 kg a bag is about 2,500 bags a month and about 100 bags a day. On a scale rated 260-300 bags/h that is 20 to 23 minutes of bagging.
The decision rule for a small volume build
The raw material is already owned, meaning logs and slabs from the mill's own stand or a neighbour's sawmill rather than bought-in dry shavings. The shift runs 2 to 3 hours a day, so the connected power is paid for over a short run. And the bedding replaces a purchase in the mill's own poultry houses, so the output has a captive buyer.
Dried material bought in at a delivered price, because the dryer and the freight are then paid twice. A single shift run at full load with no buffer, because the frame has to be three times larger. And no poultry houses of its own, because the product then has to win on price in an open market.
Hours per day against daily tonnage
The hours are the lever with the most travel. The same 1.5 tonnes per day takes 3 hours at 0.51 t/h on the flat die frame, 2 hours at 0.76 t/h at the top of its band, or 1.5 hours at 1.0 t/h on the ring die frame.
Nothing here is quoted as a price, a payback period or a saving. What the page fixes is the basis for that arithmetic: 37.5 t/month, 2,500 bags, 92 kW, 2 to 3 hours.
10
How Are the Proposal, Lead Time and Terms Structured for This Scope?
This page sets out one configuration: the complete line from the planer outlet to the bagging scale, with the press frame named and the alternative frame priced as a line item. The scope, the station list and the power total are fixed in that order.
Related
start a bedding line proposal request with the three density readings and the bag specification attached.The quotation is an . The line items are the eight stations in the table, the conveying between them, a first spare set, export packing and the technical file. , because it is not in the catalogue and the machine on site stays in service.
The decision rule for a single option proposal
One scope, one station list, one power total, and the press alternative shown as a priced line rather than as a second document.
Four fields stay open until the owner supplies data: the planer outlet size, the sustained planer output, the press inlet moisture window, and the bag type with its target weight. The density basis is the first line on that sheet, because every tonnage derives from it.
Lead time and terms window
Manufacturing and delivery time, installation, commissioning, training and the warranty period are all , and each is quoted per project rather than printed here. The clock starts when the deposit lands and the drawings are signed off, not when the enquiry was sent, and the factory test on a weighed sample sits inside that window.
Installation and training follow the same pattern: a commissioning supervisor, stated training days, and a handover on a running line. The warranty covers frames and drives and excludes wear parts, with the die and roller set treated as consumables.
The page closes on five numbers: three densities, the planer outlet size and output, the bag type and weight. Send three density readings on the three moisture bases, the planer outlet size and output, and the bag type and weight. Those five lines fix the frame, the dryer and the power total.
FAQ
FAQ: 1,000 m3 Per Year Cedar Bedding Pellet Line
1
How many tonnes per day does 1,000 m3 of cedar per year produce?
At the 18% moisture density of 380 kg/m3, 1,000 m3/year x 380 kg/m3 = 380 t/year: 1.27 t/day over 300 working days, 1.52 t/day over 250, and 0.16 to 0.19 t/h over an eight hour day. On a fresh wood basis of 500-650 kg/m3 the same volume is 500-650 t/year, so the basis is fixed first.
2
Do bedding pellets differ from fuel pellets in diameter and hardness?
Yes, in both and in what is measured. Bedding takes the small side of the die range, 4-6 mm, and a low compression ratio so the pellet softens and breaks down when wetted; it is judged on absorbency and dust. Fuel takes 6-10 mm and a hard pellet judged on calorific value, ash and durability.
3
Is a planer or chipper included with the bedding line?
No. The planer is not in our catalogue, and no machine here is offered as an equivalent to a YT 145. The existing planer stays in service and the scope begins at its outlet chute. Its outlet size and sustained output are to be confirmed from the machine's own data, because a planer below the 0.42 to 0.51 t/h shift rate caps the whole line.
4
Which press frame suits 1.5 tonnes per day of bedding pellets?
The 55 kW flat die frame rated 500-800 kg/h, which holds 1.27 to 1.52 t/day in a 2 to 3 hour shift at 0.42 to 0.76 t/h. The 90 kW ring die frame rated 1-1.5 t/h is the alternative where the mill expects to expand or switch to fuel pellets.
5
What moisture must cedar chips reach before the press?
The dryer figures on record are an inlet band of 10% to 80% and an outlet of 15%. The press inlet window for cedar shavings is to be confirmed against the factory technical confirmation sheet, and the 12%-20% printed for the feed range does not transfer to wood.
6
What connected power does a 1.5 tonne per day bedding line total?
About 92 kW with the flat die frame: 7.5 kW grinding, 11.5 kW drying, 55 kW pelleting, 5.15 kW cooling, 8 kW sieving, 3 kW bagging and 1.5 kW conveying. With the 90 kW ring die frame the total is about 127 kW. Both are Illustrative and exclude dust collection, compressed air and lighting.
Hot Tags: Industrial Wood Pellet Production Line for Poultry Bedding, China Industrial Wood Pellet Production Line for Poultry Bedding manufacturers, suppliers, factory, Compelet Wood Pellet Plant, Vertical Ring Die Wood Pellet Mill, pellet stove pellet line, wood pellet production low emission, pellet line for wood stove, mobile pellet line
You Might Also Like
Send Inquiry




