Knowledge

Key Characteristics of Screw-Extrusion Biomass Briquette Machines

What Defines a Biomass Briquette Machine

A biomass briquette machine compresses loose plant material into a dense rod using heat and pressure rather than glue. The working principle is screw extrusion: a rotating screw conveys the feedstock into a heated die, the softened lignin in the biomass acts as a natural binder, and the material leaves the die as a continuous rod that is cut to the desired length. Because there is no curing or setting stage, a machine's character is decided entirely by how it handles the three variables of the process - die temperature, screw pressure and feedstock moisture.

Characteristic 1: Wide Raw-Material Window

The press accepts a broad range of feedstocks: sawdust, crop straw, rice husk, peanut and other nutshells, wood shavings and grass. In practice the machine handles material from fine powder up to about 50 mm in length, and a feedstock moisture content from roughly 5 percent to 30 percent. That window is what makes the machine usable for a producer who buys whatever local material is available in a given month, instead of being locked to a single supplier specification.

Characteristic 2: High Throughput per Installed Kilowatt

The design is deliberately compact: pressing, heating, cutting and discharge are integrated in a single frame, so the machine occupies little floor space and needs no multi-machine line balancing. That integration reduces both manpower and connected power per tonne of output, which is why the press is used in small and medium-sized fuel plants as a standalone unit as well as in a full production line.

Characteristic 3: Automatic Electric Heating and Moisture Adjustment

The die is electrically heated, and the temperature can be set by the operator to suit the feedstock. During running the conditioning effect of the heating device adjusts the effective dryness of the material, which solves the two failures that stop production: blocking, where material jams in the die, and non-forming, where the rod crumbles on exit. With the temperature set correctly the material flows steadily and rod density stays consistent from the start of the shift to the end.

Characteristic 4: Self-Adjusting Pressure Wheel

The pressure wheel uses a bidirectional-rotation thrust bearing to adjust the pressure angle automatically. The geometry is designed so that the material neither overloads the screw nor starves the die. In plain terms, the press keeps its own balance between feed and compression, which removes the constant manual trimming that unstable presses need and keeps discharge and forming stable over long running hours.

Characteristic 5: Simple Operation and Low Manning

Once the process route for a given feedstock is established, operation is straightforward. Feeding can be done manually or automatically with a conveyor; in normal working conditions two operators are sufficient per shift. Simple structure also means fast cleaning and easy access to wearing parts, which keeps unplanned downtime short.

MKYK Series Rated Data

Model Power (kW) Die Hole Briquette Size (mm)
MKYK-36 45 36 32 x 32 x 50-100
MKYK-48 75 48 32 x 32 x 50-100
MKYK-72 110 72 32 x 32 x 50-100
MKYK-90 132 90 32 x 32 x 50-100
MKYK-120 200 120 32 x 32 x 50-100
MKYK-150 250 150 32 x 32 x 50-100

All models produce a square-section rod of 32 x 32 mm cut to 50-100 mm. Higher die-hole counts increase throughput at the same rod size, so the choice between models is a question of required tonnes per hour rather than of product form.

Where the Process Can Go Wrong

Instability almost always traces back to the feedstock. Material that is too dry will not develop sufficient lignin softening and the rod cracks; material that is too wet flashes to steam inside the die and the rod expands on exit. Abrasive contamination such as sand or small stones wears the screw and the die far faster than the material itself would. Screening the feedstock and holding the moisture level steady are therefore worth more than any adjustment made at the machine.

Frequently Asked Questions

Q: Does a briquette machine need a binder or adhesive?
A: No. Heat and pressure in the die soften the lignin in the biomass, and the lignin itself bonds the particles. Adding adhesive is unnecessary at a normal moisture level and adds cost per tonne.

Q: What moisture content can the machine accept?
A: A feedstock moisture content from roughly 5 percent to 30 percent can be handled, with the electric heating device used to compensate for variation. Stable moisture in the middle of that range gives the most consistent rod density.

Q: What briquette size does the MKYK series produce?
A: A square-section rod of 32 x 32 mm, cut to lengths of 50-100 mm on all six models from MKYK-36 to MKYK-150.

Q: How many operators are needed per shift?
A: Two operators are normally sufficient. With a conveyor for automatic feeding the labour requirement stays the same as capacity increases, which is where the cost advantage of the larger models comes from.

Q: Why does the rod sometimes crumble as it leaves the die?
A: Non-forming is usually caused by feedstock that is too dry or by die temperature that is too low. Raising the temperature of the electrically heated die and adjusting moisture restores forming without changing any mechanical setting.

Q: How are briquettes specified for sale?
A: Graded wood briquettes are covered by ISO 17225-3, which sets classes and property limits in the same way ISO 17225-2 does for pellets. Buyers commonly test moisture by ISO 18134 and ash content by ISO 18122.

You Might Also Like

Send Inquiry