Products

100 kg/h Biomass Pellet Production Line for Vine Leaves, Branches and Wood
video
100 kg/h Biomass Pellet Production Line for Vine Leaves, Branches and Wood

100 kg/h Biomass Pellet Production Line for Vine Leaves, Branches and Wood

This article explains what equipment a 100 kg/h biomass pellet production line needs, how each material is prepared, and the power and space required.

Features

01

Quick Answer: What Equipment Does a 100 kg/h Biomass Pellet Line Need?

A 100 kg/h biomass pellet production line is designed to process prepared agricultural and wood waste into biomass fuel pellets. The proposed configuration includes an MH-420 multifunctional crusher, screw conveyor, 0.8 × 8 m rotary drum dryer, RKL-250 flat die pellet press, cooler screener and bucket elevator.
The flat die pellet press has a nominal capacity of 100–200 kg/h and a 15 kW main motor. The drum dryer uses steam supplied by an external boiler.
Based on the itemized equipment powers, the connected electrical load is approximately 39.2 kW, using a 0.75 kW bucket elevator. The original 40.7 kW figure requires confirmation against the final elevator motor and electrical equipment list.
The line can be configured for vine leaves, branches, firewood and selected waste paper mixtures. Feedstock preparation, moisture control and material testing are essential for consistent pellet quality.
02

What Materials Can a 100 kg/h Biomass Pellet Production Line Process?

The proposed line is designed for four types of biomass and recyclable material: vine leaves, branches, firewood and waste paper.
Each material has different moisture, density, fiber length and ash characteristics. These differences affect crushing, drying, pellet formation and die wear.
Raw Material
Typical Incoming Condition
Preparation
Processing Consideration
Vine leaves
Loose material; approximately 20–40% moisture
Crushing and drying
High ash and variable fiber structure
Branches
Up to 15 cm; approximately 20–35% moisture
Chipping and crushing
Requires suitable cutting equipment
Firewood
Split wood; approximately 15–20% moisture
Size reduction and moisture adjustment
Relatively dense biomass
Waste paper
Dry, loose or baled
Shredding and screening
Fiber and mineral filler affect pellet durability
Table 1. Proposed feedstock categories and preparation requirements. Actual moisture ranges must be confirmed through sampling.
 

Can Different Materials Be Processed in One Machine?

Yes. The MH-420 multifunctional crusher combines a chipping rotor and hammer section, allowing it to process branches and smaller materials using suitable screens and operating settings.
However, one crusher does not mean every material can be processed under identical conditions.
Branches may require more cutting action, while leaves and paper need appropriate crushing and screening. Feedstock changes should be accompanied by inspection of particle size and moisture.
Waste paper is best evaluated as a controlled component of a biomass mixture. Its fiber length, mineral filler and composition influence pellet durability. It should not automatically be assumed that all waste paper is suitable for fuel pellet production.
03

What Machines Are Included in the 100 kg/h Pellet Production Line?

The proposed line consists of six main machine assemblies, plus a manual bagging station.
Equipment
Model
Installed Power
Main Function
Multifunctional Crusher
MH-420
7.5 kW
Chipping and crushing
Screw Conveyor
KWX50YP
1.5 kW
Transfers crushed material
Rotary Drum Dryer
0.8 × 8 m
4.0 kW
Drum drive
Dryer Fan
Matching dryer
7.5 kW
Air circulation
Flat Die Pellet Press
RKL-250
15 kW
Pellet formation
Cooler and Screener
GMC-LQSF50
2.95 kW
Cooling and screening
Bucket Elevator
TDSG10-18
0.75 kW listed
Material lifting
Bagging Station
Manual
0 kW
Weighing and bagging
Table 2. Proposed equipment list. The elevator motor rating and final total connected load must be confirmed before electrical design.
 

How Does the Production Process Work?

Raw Material → Crushing → Conveying → Drying → Pelletizing → Cooling and Screening → Packaging
The crusher reduces branches, leaves and other feedstocks into suitable particles. The screw conveyor transfers the material to the drying section.
The rotary drum dryer adjusts the moisture content using heat supplied by the steam system. After moisture testing, the prepared biomass enters the flat die pellet press.
The press compresses the material through die holes to form pellets. The cooler then reduces pellet temperature, while screening removes loose fines before bagging.
 

Why Is the Crusher Rated Higher Than the Pellet Press?

The MH-420 has a catalogue capacity of 600–1,000 kg/h under specified conditions, while the RKL-250 press is rated at 100–200 kg/h.
The crusher requires sufficient capacity to supply the press after the screen aperture, material density and feedstock type are taken into account.
A finer screen can significantly reduce crushing throughput. Therefore, the final crusher output should be tested with the actual raw material and required particle size.
04

How Does the Steam-Heated Drum Dryer Work?

The proposed 0.8 × 8 m rotary drum dryer uses a steam coil to provide heat for moisture removal.
The steam is supplied by an external boiler through a control valve, with condensate removed through a suitable steam trap and return system.
The listed boiler output is 300 kW, but this is a site utility specification rather than the confirmed thermal demand of the 100 kg/h pellet line.
Item
Specification
Notes
Drum diameter
0.8 m
Proposed equipment dimension
Drum length
8 m
Proposed equipment dimension
Boiler output
300 kW
External site equipment
Drum motor
4.0 kW
Mechanical drive
Dryer fan
7.5 kW
Air circulation
Steam connection
Coil and condensate return
Site interface
Table 3. Proposed steam dryer configuration.
 

Is a 300 kW Boiler Necessary for a 100 kg/h Pellet Line?

Not necessarily for the drum dryer alone.
A 300 kW boiler may serve a wider factory or several pieces of equipment. The actual thermal demand of the dryer depends on feedstock throughput, initial moisture, final moisture, evaporation rate and heat losses.
For accurate boiler selection, calculate the required water evaporation rate first.
For example, the water removal requirement can be estimated from the incoming and target moisture contents on a wet basis.
A larger boiler does not automatically increase pellet production capacity. Dryer dimensions, airflow, heat-transfer performance and material residence time determine drying performance.
 

Why Use a Rotary Drum Dryer?

A rotary drum moves and mixes material continuously as it travels through the drying chamber.
This is useful when processing different feedstocks with varying bulk density and particle shapes. However, leaves and paper fines require appropriate airflow control and dust protection to reduce material loss.
05

What Moisture and Particle Size Are Required Before Pelletizing?

The proposed target moisture content at the pellet press is approximately 12–15%, with a particle size of around 3–5 mm.
These are operating targets, not universal values for every biomass material.
Feedstock
Moisture Consideration
Preparation Requirement
Vine leaves
May arrive at 20–40%
Dry and crush
Branches
May arrive at 20–35%
Chip, crush and dry
Firewood
May arrive at 15–20%
Reduce particle size and adjust moisture
Waste paper
Often below 10%
Shred and test; drying may not be necessary
 

How Is Moisture Controlled?

Moisture should be measured using representative samples from the dryer discharge.
An operator should check the moisture before feeding the press and adjust dryer conditions when the material falls outside the agreed operating range.
Paper-heavy mixtures require particular attention. Very dry, short-fiber material may not form durable pellets without an appropriate blend and suitable pressing conditions.
06

How Much Power Does the Biomass Pellet Line Consume?

The itemized electrical load is approximately 39.2 kW using the listed 0.75 kW bucket elevator.
Equipment
Power
MH-420 Crusher
7.5 kW
KWX50YP Conveyor
1.5 kW
Drum Drive
4.0 kW
Dryer Fan
7.5 kW
RKL-250 Pellet Press
15 kW
GMC-LQSF50 Cooler
2.95 kW
TDSG10-18 Elevator
0.75 kW
Calculated Total
39.2 kW
Table 4. Electrical load calculated from the listed individual equipment ratings.
The original equipment description states 40.7 kW. This difference should be reconciled against the elevator nameplate, control cabinet and any omitted auxiliary motors before publishing a final power specification.
The steam boiler is not included in the electrical total because its thermal energy comes from fuel. Boiler auxiliaries, pumps and other site equipment may add electrical loads.
 

What Electrical Supply Is Required?

The line should use an appropriately sized three-phase electrical supply. Final transformer, cable, breaker and motor starter selection must consider motor starting current, power factor and simultaneous operation.
The largest listed motor is the 15 kW pellet press, followed by the 7.5 kW dryer fan and crusher.
07

What Floor Space and Maintenance Are Required?

The preliminary machine layout requires approximately 14 m × 3.5 m, with about 5 m of clear height under the dryer arrangement.
A separate covered feedstock storage area is recommended, particularly for leaves and waste paper, which can absorb moisture from humid air.
The boiler should be positioned near the dryer where practical, while allowing suitable maintenance and safety clearance.
 

Which Components Wear First?

Equipment
Main Wear Components
Crusher
Hammers, cutting components and screens
Pellet press
Flat die and rollers
Dryer
Bearings, drive components and seals
Cooler
Bearings and screening components
Conveyor and elevator
Belts, buckets and bearings
Vine leaves can introduce ash and mineral material, while waste paper may contain mineral fillers. These characteristics can increase wear at the die and rollers.
Recommended spare parts include one spare die, one roller set, a hammer set, two screens, drum bearings and drive belts.
08

How Is the Biomass Pellet Production Line Installed?

Installation starts with machine positioning and leveling, followed by mechanical connections, electrical installation and steam system testing.
The steam coil, control valve, steam trap and condensate return should be checked before the dryer is loaded with material.
The production sequence should then be tested:
1.
Check the crusher and screen.
2.
Verify conveyor direction and material transfer.
3.
Test the drum drive and steam system.
4.
Measure dryer discharge moisture.
5.
Adjust pellet press die and rollers.
6.
Test pellet cooling and screening.
7.
Conduct a loaded production trial using the buyer's feedstock.
Training should cover crusher screen changes, dryer moisture control, pellet press adjustment and finished pellet inspection.
The site should provide a level floor, suitable roofing, three-phase power, a covered feedstock bay and an approved steam supply where steam heating is selected.
09

What Does the Quotation Include?

The proposed supply package includes the main processing machines, conveying equipment, control cabinet and recommended spare parts.
The external boiler, steam pipeline, condensate return, foundations and factory building should be listed separately unless included in the signed supply contract.
 

Information Required for a Customized Quotation

Please provide:
▪
Feedstock types and approximate material ratios.
▪
Moisture content of each material.
▪
Required pellet diameter and length.
▪
Desired production capacity per hour.
▪
Available boiler output and steam conditions.
▪
Electrical supply and factory dimensions.
▪
Destination port and delivery location.
Contact our team for a customized biomass pellet production line quotation.
Explore our wood pellet production lines and biomass briquette machines.
Related
500 kg/h small wood pellet production line and 1-1.5 t/h biomass pellet machine line.
10

Frequently Asked Questions About 100 kg/h Biomass Pellet Lines

1
What is the capacity of the RKL-250 pellet press?
The stated nominal capacity is 100–200 kg/h. Actual production depends on material composition, moisture, particle size and die configuration.
2
Can vine leaves be made into biomass pellets?
Yes, but the material should be tested and appropriately prepared. Leaf-only pellets may have different density, ash content and durability from wood-based pellets.
3
Can the line process waste paper?
Selected waste paper can be evaluated as a feedstock or mixture component. Its fiber structure, mineral filler and suitability for the intended fuel application must be checked.
4
What particle size is required?
The proposed target is 3–5 mm before pelletizing. The ideal particle size depends on the feedstock and press configuration.
5
What moisture is required before pelletizing?
The proposed operating target is approximately 12–15%, subject to material testing.
6
Does the line require a 300 kW boiler?
The listed 300 kW boiler is a proposed site utility. The actual dryer thermal requirement should be calculated from the material and moisture removal rate.
7
How much electrical power does the line need?
The listed equipment ratings add up to approximately 39.2 kW using the 0.75 kW elevator value. The final total needs confirmation.
8
How many workers are required?
Two operators are proposed: one for material preparation and drying, and another for pellet pressing and bagging. Actual staffing depends on automation and shift length.
9
How much factory space is needed?
The preliminary machine row requires approximately 14 m × 3.5 m with around 5 m clear height, plus separate storage space.
10
Can the dryer use an existing factory boiler?
Yes, if the boiler can provide the required steam pressure, temperature and thermal capacity. The steam connection and condensate return must be engineered for the dryer.
biomass pellet production line
wood pellet production line
Customer visit

Hot Tags: 100 kg/h Biomass Pellet Production Line for Vine Leaves, Branches and Wood, China 100 kg/h Biomass Pellet Production Line for Vine Leaves, Branches and Wood manufacturers, suppliers, factory, wood stove pellet line, wood pellet line, Small biomass pellet production line, Wood chip fuel pellet production line, Burn resistant biomass pellet production line, biomass pellet lines

You Might Also Like

(0/10)

clearall