Knowledge

Biomass Compression Equipment: Working Principle and Configuration of the MKYK Briquette Press

Emma Davis
Emma Davis
As a senior quality control engineer, Emma ensures that every rod making machine meets the highest industry standards. Her attention to detail and commitment to excellence have earned her recognition within the company.

What Biomass Compression Equipment Does

Biomass compression equipment turns loose material - sawdust, straw, nutshells, wood shavings - into dense rod-shaped briquettes. The value of the process is not the shape but the density: a briquette stores in less space, can be handled by bulk equipment, resists moisture pick-up better than loose material, and burns with a steadier flame. The MKYK series is a screw-extrusion press built for continuous production, and its performance in daily work is decided by three variables: die temperature, screw pressure and feedstock moisture.

How the Compression Process Works

In a screw-extrusion briquetting press, a rotating screw conveys feedstock into a heated forming die. The heating system softens the lignin naturally present in the biomass, and that softened lignin acts as a binder, so the material is compressed and bonded into a continuous dense rod as it is forced through the die. No chemical adhesive is used. The rod is extruded, cut and discharged in uniform lengths. Result quality depends on the temperature in the die, the pressure the screw develops and the moisture content of the feedstock; change any one of the three and the density of the rod changes with it.

MKYK Series Specification Table

Model Rated Power (kW) Die Hole Capacity (t/h) Briquette Size (mm)
MKYK-36 45 36 1.0-1.5 32 x 32 x 50-100
MKYK-48 75 48 1.5-2.5 32 x 32 x 50-100
MKYK-72 110 72 2.5-3.5 32 x 32 x 50-100
MKYK-90 132 90 3.5-5.0 32 x 32 x 50-100
MKYK-120 200 120 4.0-6.0 32 x 32 x 50-100
MKYK-150 250 150 6.0-10.0 32 x 32 x 50-100

The series covers a capacity range from 1.0 to 10.0 t/h. All models produce square-section briquettes of 32 x 32 mm with a length of 50-100 mm, so product form is constant across the range and only throughput changes.

Operating Characteristic 1: Compact Structure and Simple Operation

The layout is compact and rational, so operators learn the workflow quickly and daily cleaning and part access are straightforward. Production functions are integrated in one unit, which saves manpower and electrical demand compared with multi-machine arrangements of the same output. Simplicity in this class of machine is not a compromise; it is what keeps unplanned downtime short in a plant that runs one shift or two.

Operating Characteristic 2: Wide Raw-Material Applicability

Sawdust, crop straw, rice husk, nutshells and wood shavings can all be formed into rods directly, without a change of machine configuration. Producers who switch feedstock by season or by local supply therefore keep running through the year. The practical limits are moisture above roughly 18-20 percent, which needs drying, and oversize particles, which need re-grinding for consistent density.

Operating Characteristic 3: Automatic Temperature Control and Electric Heating

An automatic electronic temperature control system lets the operator set the molding temperature for the feedstock in use and shows the working status of the machine directly. A fully automatic electric heating device conditions the material's dryness and humidity during running, which addresses the two common production failures: blocking, where material jams the die, and non-forming, where briquettes crumble on exit. Correct heating raises both molding rate and overall efficiency, because fewer restarts are needed after a blockage.

Operating Characteristic 4: Self-Adjusting Pressure Wheel

The pressure wheel uses a bidirectional-rotation thrust bearing to adjust the pressure angle automatically. The machine geometry is arranged so that the material neither overloads the screw nor starves the die, which keeps discharge and molding stable over long running hours. Stable extrusion also means a more consistent rod density, and consistent density is what buyers of briquette fuel actually pay for.

Matching a Model to Daily Output

Selection follows daily feedstock volume and required output. The MKYK-36 at 1.0-1.5 t/h suits small workshops and farm-scale plants; the MKYK-72 to MKYK-90 at 2.5-5.0 t/h covers medium commercial production; and the MKYK-120 and MKYK-150 at 4.0-10.0 t/h serve large briquette and pellet plants running continuously. In every case, confirm that the moisture content of the local feedstock can be brought into the working range of the heating system, because moisture is the variable that most affects molding stability.

Verifying Briquette Quality

Product claims in this industry should be measurable. Graded wood briquettes are covered by ISO 17225-3, which sets classes and property limits; moisture content is determined by the oven methods of ISO 18134, ash content by ISO 18122 and calorific value by ISO 18125. Bulk density is determined by ISO 17828. A batch that can be tested against these methods gives the buyer a defensible basis for price and gives the producer a target for the machine settings.

Frequently Asked Questions

Q: What is the capacity of the largest MKYK model?
A: The MKYK-150 runs at 6.0-10.0 t/h with a 250 kW motor and a 150-hole die. The smallest unit, the MKYK-36, runs at 1.0-1.5 t/h with a 45 kW motor.

Q: Does the press require an adhesive or additive?
A: No. The die heating softens the lignin in the biomass and the lignin bonds the particles together. Only where a specific feedstock will not form at all is a small amount of binder considered, and it is not part of normal operation.

Q: What briquette dimensions are produced?
A: Square-section briquettes of 32 x 32 mm, cut to 50-100 mm in length, on every model in the range.

Q: What causes blocking in the die?
A: Feedstock moisture that is too high, die temperature that is too low, or a feed rate that exceeds the screw's conveying capacity. The automatic heating device and temperature control correct the first two; the third is a matter of matching the feed conveyor to the press.

Q: How should feedstock be prepared before pressing?
A: Remove abrasive contamination such as sand and metal, reduce particle size to a consistent grade and bring moisture into the working range. Screening and grinding cost less than the die and screw wear caused by skipping them.

Q: Can the same machine run on straw and on sawdust?
A: Yes. The feedstock window covers sawdust, straw, rice husk, nutshells, shavings and grass. What changes between materials is the die temperature and the moisture setting, not the machine itself.

You Might Also Like

Send Inquiry