Biomass Molding Machine Maintenance: Roller, Die and Grease Schedule
Daily Checks Before and After Each Shift
Maintenance of a biomass molding machine is mostly a routine of short inspections rather than occasional repairs. Before production, check the clearance between the compression roller and the die, confirm that the roller position is correct, verify that all fastening screws are tight, and confirm that the lubricant level is sufficient. Roller bearings, main shaft bearings and the gearbox are the assemblies that fail first when lubrication is neglected, so treat the grease schedule as a production task rather than a workshop task. After production, inspect the pressing chamber for hard objects, clean residues from the die face and record the running hours and tonnage produced.
Keep a written log for each machine: date, running hours, tonnes produced, grease quantity added, parts replaced and any abnormal noise or current reading. The log converts maintenance from guesswork into a schedule.
Roller to Die Clearance and Position Adjustment
The roller must press material into the cavities without touching the die surface. Clearance that is too wide leaves a slipping layer of material, so output drops and the die glazes; clearance that is too tight produces metal-to-metal rubbing, rapid wear and a rising current draw. In normal workshop practice the working gap is set with a feeler gauge to about 0.1 to 0.3 mm, then checked again after the first hour of running because the assembly settles under load. Loosen the locking nut, turn the adjusting bolt or eccentric, verify the gap at several points around the die, and tighten the lock nut firmly. Check the gap at every roller, not only at one position.
If the die is unevenly worn, output falls along part of the ring. Regrind or resurface the die rather than compensating with excessive roller pressure, which shortens bearing life.
Die Care, Cleaning and Storage
The die is the most expensive wear part of the machine. Keep the inside of the ring die clean, keep cavity entries free of carbonised material, and never use a hammer to open a jammed chamber: impact damages the smooth surfaces of the die and the roller shells. Remove stones, metal scrap and other hard inclusions as soon as they are found, because they score the cavity walls and cause pellets or blocks with torn edges. When the machine is stopped for a long period, press material of higher moisture content through the die to fill the cavities. This packed layer prevents corrosion of the hole walls and reduces the starting load next time.
Store spare dies flat, oiled and covered, away from damp floors. Rust inside the cavity changes friction, which changes the temperature and output of the whole pressing chamber.
Lubrication and Fastener Control
Grease roller bearings on the interval set by running hours, using a grease of the grade recommended for the bearing and the ambient temperature; clean the grease nipple before attaching the gun so that grit is not injected into the bearing. Check the gearbox oil level daily and change the oil at the interval stated for the duty cycle. Fasteners around the die holder, roller arms, hopper and base frame work loose under vibration and must be re-torqued at the specified value; a loose die holder causes uneven load, which shows as pulsation in the motor current.
Driveline components need the same discipline: check belt tension and alignment, look for glazing or cracking on belts, check coupling elements for wear and confirm that guards are refitted correctly after every intervention.
Wear Limits and Replacement Signals
| Component | Inspection interval | Warning signal |
|---|---|---|
| Compression roller shell | Every shift | Output drop, flat spots, visible grooving |
| Die cavity entry | Weekly | Rounding of edges, blocks with torn surfaces |
| Roller bearing | Weekly by sound and temperature | Noise, heat, grease discolouration |
| Gearbox oil | Daily level, periodic change | Metal particles, milky colour |
| Fasteners | Daily | Loose die holder, current pulsation |
| Guards and interlocks | Daily | Missing bolts, damaged hinge or switch |
Shutdown, Packing and Restart
Before a planned stop, run high moisture material through the die to pack the cavities, then stop the feed, let the chamber empty and switch off in the sequence given in the operating manual. On restart, heat the die to working temperature, run the machine without feed until the rollers turn freely, then introduce material slowly and raise the feed rate to normal over several minutes. A cold die fed at full rate is the most common cause of a sheared safety pin or a tripped overload.
Safety and Compliance Points
Maintenance work is governed by ISO 12100 for risk assessment, IEC 60204-1 for the electrical equipment of machines, ISO 13849-1 for safety-related control functions, ISO 14120 for fixed guards and ISO 14119 for interlocking devices. Dust control in the hall follows NFPA 664 practice for wood processing. Never open a guard while the machine is running, and always isolate and lock off the supply before reaching into the pressing chamber.
Frequently Asked Questions
Q: How often should roller clearance be checked?
A: Check it before every shift and re-verify after the first hour of running. A gap of roughly 0.1 to 0.3 mm measured with a feeler gauge is typical workshop practice, but always follow the figure stated in the machine manual.
Q: Is it necessary to pack the die before a long stop?
A: Yes. Pressing higher moisture material through the die fills the cavities, prevents rust inside the holes and lowers the starting load when production resumes.
Q: Why is output falling while motor current rises?
A: This combination points to a worn or glazed die, a roller that is too tight, or feedstock that is too dry. Inspect the die cavity entry first, then check clearance, then confirm feed moisture against the target range of 12% to 15%.
Q: Can a hammer be used to free a jammed chamber?
A: No. Impact damages the smooth working surfaces of the die and rollers. Switch off, isolate, open the chamber, remove the obstruction and clean the cavity entries with a soft scraper.
Q: How is machine output quality verified after maintenance?
A: Take a sample after the machine reaches steady state and test mechanical durability to ISO 17831-1 for pellets or ISO 17831-2 for briquettes. Compare the result with the previous record to confirm that the maintenance work restored performance.

