Knowledge

How to Use a Biomass Briquette Machine: Operator Setup and Feeding Guide

What a Biomass Briquette Machine Does

A biomass briquette machine densifies loose agricultural and forestry residue into solid, uniform briquettes without any chemical binder. Feedstock that arrives with a bulk density of about 80-150 kg/m³ leaves the press as briquettes with a density of 800-1,200 kg/m³. The binding force comes from lignin, the natural polymer in plant fibre, which softens in the compression zone under heat and pressure and then re-solidifies as the briquette cools.

Finished briquettes substitute for coal, firewood, fuel oil, diesel and light diesel oil in three main duties:

Industrial steam boilers in textile mills, food processing plants, chemical works, brick kilns, refractory and ceramic plants.

Drying kilns and process heat for tea processing, tobacco curing, timber drying, milk plants, solvent extraction and leather finishing.

Gasification systems that convert briquettes into syngas for power generation or direct process heat.

Because a briquette is dense, free-flowing and low in dust, it stores and conveys like a conventional solid fuel. For plants facing emissions limits on coal, it is a drop-in fuel that needs only feed-rate tuning, not a new combustion system.

Model Range and Technical Specifications

The MKYK series covers workshop-scale and mid-size industrial production. All models share a square 32 x 32 mm die profile and cut the extruded rod to a length of 50-100 mm, so the choice of model is driven by the required hourly output and the available power supply.

Model Motor power Die holes Briquette size
MKYK-36 45 kW 36 32 x 32 x 50-100 mm
MKYK-48 75 kW 48 32 x 32 x 50-100 mm
MKYK-72 110 kW 72 32 x 32 x 50-100 mm
MKYK-90 132 kW 90 32 x 32 x 50-100 mm
MKYK-120 200 kW 120 32 x 32 x 50-100 mm
MKYK-150 250 kW 150 32 x 32 x 50-100 mm

Nominal output depends on feedstock type, particle size and moisture, so treat the model number as a power class rather than a guaranteed tonnage. Confirm the working rate with a trial run on your own material.

Pre-Start Checks and Machine Setup

Feedstock: screen the material so no particle is larger than 5-6 mm, and keep moisture in the 8-15% range on a wet basis. Oversize chips and wet slugs are the two most common causes of a blocked die.

Foundation: mount the machine on a level concrete floor rated for the dynamic load and bolt the base frame down. Vibration loosens anchors and spoils briquette density.

Power: the drive is 380 V three-phase. Verify the phase sequence before the first start, because a reversed phase spins the main shaft backwards and damages the die within seconds. Set the overload relay a little above the motor full-load current.

Lubrication: check the gearbox sight glass and top up with ISO VG 220 industrial gear oil for ambient temperatures above 15 °C. Grease the main shaft and roller bearings daily with lithium-based EP2 grease.

Cleanliness: remove hardened residue left from the previous shift and confirm that the ram or screw turns freely by hand.

Warm-Up, Feeding and Quality Control

Never feed production material into a cold compression chamber. Start the main motor with the hopper gate closed and run it unloaded for 2-3 minutes, listening for knocking, grinding or a rhythmic thump. Then open the gate partially and run 10-15 minutes of dry, low-value material such as coarse sawdust or ground rice husk at 50-70% feed rate. A stamping press should reach roughly 150-180 °C on the die surface and a screw-type press about 220-280 °C.

Once the die is hot and warm-up briquettes form cleanly, switch to production feedstock gradually over 2-3 minutes. Set the feed rate so the main motor draws 80-90% of its rated full-load current: below 70% wastes capacity, above 95% invites over-current trips whenever material density varies. Watch the ammeter rather than the discharge chute:

A sudden current spike means a foreign object, an oversize particle or a wet slug has entered the compression zone. Cut the feed immediately and inspect if the spike does not clear.

A gradual drop means the hopper is bridging. Tap the hopper wall with a mallet or fit a mechanical vibrator; never reach into the hopper.

A regular cyclic swing of 5-10% is normal on a stamping press as the ram cycles; an irregular pattern points to uneven feeding.

Pull a sample briquette every 30 minutes. Good briquettes are smooth with a slight sheen from plasticised lignin. Drop one from 1 m onto concrete: it should survive with minor edge spalling. If it shatters, raise the feedstock moisture by 1-2% or reduce the roller-to-die gap, which is normally set to 0.5-1.0 mm measured cold with a feeler gauge.

Shutdown, Maintenance and Troubleshooting

Shutdown is as important as startup. Close the hopper gate but keep the machine running, purge with 2-3 kg of dry coarse sawdust or rice husk until the current falls, then stop the main motor. Clean the die face while it is still warm using a brass scraper or a soft wire brush; never use a steel chisel on a hardened die. If the machine will stand idle for more than 24 hours, apply a light coat of SAE 30 oil to the die face and rollers to prevent rust.

Symptom Likely cause Corrective action
Briquettes crumble or stay soft Moisture too low, die too cold, roller gap too wide Add 1-2% moisture, extend warm-up, close the gap to 0.5-1.0 mm
Surface cracks on briquettes Dry feedstock, coarse particles, cold die Recheck moisture, screen below 5 mm, lengthen warm-up
Current spike or jam Oversize particle, foreign object, wet material Stop the machine, clear the chamber, re-screen the feedstock
Output falling off Worn die or roller, wrong feed rate, hopper bridging Inspect wear parts, reset feed rate, fit a hopper vibrator
Smoke at the die area Feedstock too dry, excess friction Correct moisture and reduce feed rate temporarily

Track die and roller wear in an operating log. Die life is driven mainly by feedstock abrasiveness, so rice husk and straw blends wear dies faster than clean hardwood sawdust.

Frequently Asked Questions

Q: What moisture content should biomass feedstock have before briquetting?
Most technologies work best between 8% and 15% moisture on a wet basis. Wetter material produces soft briquettes and blocks the die; drier material fails to plasticise and the briquettes crumble.

Q: Is a binder needed to make biomass briquettes?
No. Heat, pressure and the natural lignin in the fibre bind the material. Lignin-rich hardwood sawdust binds best, while straw and rice husk are usually blended with woody residue.

Q: How long should the machine be warmed up before production?
Run 2-3 minutes unloaded, then 10-15 minutes on dry scrap material at 50-70% feed rate until the die reaches its working temperature and briquettes form cleanly.

Q: What current should the main motor draw in normal production?
Target 80-90% of the rated full-load current. Persistent readings above 95% indicate overfeeding or a worn die, while readings below 70% waste capacity.

Q: Can one machine handle sawdust, rice husk and straw?
Yes, with adjustments. Rice husk and straw are more abrasive and lower in lignin, so blend them with sawdust, keep particles smaller and expect faster die wear.

Q: Why must the die be purged and cleaned at shutdown?
Residue left in the die holes hardens overnight and must be chiselled out the next morning. Purging with dry material and cleaning the warm die face keeps the next startup short and safe.

You Might Also Like

Send Inquiry