Knowledge

Maintaining Biomass Briquette Equipment for Stable Briquette Quality

Why Regular Maintenance Is Essential for Briquette Equipment

A biomass briquette machine works under extremely high pressure, so the pressing chamber, the screw, the die and the bearings are loaded every second of the shift. Without a fixed maintenance routine, small faults such as a loose bolt, a dry bearing or a partially blocked die grow quickly into expensive failures. Well-maintained briquette equipment produces briquettes with consistent density and low ash content, consumes less energy and lasts several times longer than a neglected machine.

Daily Inspection Routine

Start each day with a five-minute check before loading any material. Verify that the bolts on the frame and the die are tight, that no foreign objects are in the hopper and that the lubricant level is normal. Listen for abnormal noise during the first minutes of operation and watch for vibration or material leaking from the joints. At the end of the day, clean residual material from the hopper, the pressing chamber and the discharge channel so that nothing hardens overnight. A daily routine takes minutes and prevents most sudden breakdowns.

Bolts on the frame and die: tight, with no visible thread gap.

Hopper: free of metal scrap, stones and hardened material.

Lubricant level and grease condition: normal, with no dark or gritty grease.

Running sound and vibration: stable, with no rhythmic knocking.

Lubrication: Bearings, Gearbox and Moving Parts

Lubrication is the core of briquette machine maintenance. The main bearings and the screw support bearings must be greased regularly with a high-temperature grease, because the pressing chamber generates substantial heat during operation. Check the gearbox oil level weekly and replace the gear oil at the interval recommended by the manufacturer, typically around 1000 working hours. Use only the specified lubricant grade and never mix different types of grease or oil. Over-lubrication is as harmful as under-lubrication, because excess grease heats up and damages the seals.

Lubrication point Interval Action
Main bearings Weekly High-temperature grease, checked for contamination
Screw support bearings Weekly High-temperature grease, correct fill quantity
Gearbox oil Level checked weekly, oil change about 1000 h Drain fully, clean the tank, refill with the specified grade
Moving linkages Monthly Clean and re-grease

Wearing Parts: Screw, Die and Liners

The screw tip, the die sleeve and the inner liners of the pressing chamber wear fastest because they stay in direct contact with abrasive biomass fibers. Inspect the screw tip regularly; when the thread profile is visibly worn or briquette density starts to drop, replace the tip before it damages the die. Check the die sleeve for scoring and for enlargement of the holes. Keeping a set of spare wearing parts on site is the most practical way to avoid long downtime. Wear rate depends on the material: straw and rice husk are more abrasive than softwood sawdust, so machines running field crop residues need more frequent replacement.

Protecting the Electrical Cabinet and the Working Environment

The electrical control cabinet is the most sensitive part of the equipment. Keep the cabinet door closed during operation, clean dust from the heat sink and the contactors regularly, and place moisture-absorbing desiccant inside if the workshop is humid. Check cables for abrasion and terminals for tightness at least once a month. The machine should run in a dry, well-ventilated room away from water sources and corrosive dust. When the machine stands idle for more than a few days, cover it and switch off the main power supply.

Frequently Asked Questions

Q: How often should the gearbox oil be changed?
Replace the gear oil after about 1000 working hours, or at the interval stated by the manufacturer. Drain the old oil completely and clean the oil tank before refilling.

Q: What grease should be used for the main bearings?
Use high-temperature grease for the main bearings and the screw support bearings, because the pressing chamber generates strong heat during operation.

Q: When should the screw tip be replaced?
Replace the screw tip when the thread profile is visibly worn or when briquette density begins to drop. Keeping spare tips on site avoids long downtime.

Q: How should the electrical cabinet be protected in a humid workshop?
Keep the cabinet door closed, clean dust regularly, keep the heat sink free, and place desiccant inside the cabinet. Operate the machine away from water sources.

Q: Why do briquettes have low density after months of use?
Low density usually comes from worn screw tips or die sleeves, or from a drop in material moisture. Check the wearing parts first, then re-test raw material moisture.

Q: How many spare parts should be kept in stock?
Keep at least one spare screw tip, one die sleeve and one set of liners, so a worn part can be changed during the same shift instead of stopping production for days.

You Might Also Like

Send Inquiry