How to Describe a Biomass Briquette Press Machine
A biomass briquette press machine is a compression moulding machine that squeezes crop straw, corn stalks, branches, forage grass, sawdust and wood shavings into dense solid blocks. Where a pellet mill produces small cylinders for automated boilers, a briquette press forms larger blocks - commonly 32 by 32 mm in cross-section and 50 to 100 mm long - that burn steadily in stoves, furnaces and industrial heaters. Because the block is compressed from dry biomass it is a direct substitute for firewood or coal, burns with little smoke and gives a longer burn time per kilogram.
Working Features to Describe
The machine combines a high pressing force with an automatic electric heating device. The heat softens the lignin at the surface of the biomass so that the briquette bonds without glue, while wear-resistant material in the screw, sleeve, piston or mould keeps the contact parts durable in continuous service. The structure is compact, with a small footprint, a simple layout and low labour and electricity demand per tonne compared with handling the same residue by hand. These features are why the press is a common choice for farms, small fuel workshops and heating enterprises that want to turn local crop residue into a saleable fuel.
Typical Technical Specifications
The table below gives the common specification range for screw-type biomass briquette presses. Actual figures depend on the machine design and on the raw material being processed.
| Frame | Motor Power | Mould Holes | Capacity for Biomass | Briquette Size (mm) |
|---|---|---|---|---|
| Small frame | 45 kW | 36 | 1.0-1.5 t/h | 32 x 32 x 50-100 |
| Small-medium frame | 75 kW | 48 | 1.5-2.5 t/h | 32 x 32 x 50-100 |
| Medium frame | 110 kW | 72 | 2.5-3.5 t/h | 32 x 32 x 50-100 |
| Medium-large frame | 132 kW | 90 | 3.5-5.0 t/h | 32 x 32 x 50-100 |
| Large frame | 200 kW | 120 | 4.0-6.0 t/h | 32 x 32 x 50-100 |
| Largest frame | 250 kW | 150 | 6.0-10.0 t/h | 32 x 32 x 50-100 |
As a rule of thumb, motor power scales with output: roughly 45 kW supports about one tonne per hour, while 250 kW supports six to ten tonnes per hour depending on material density and moisture. Mould hole count reflects the number of forming channels on the die, and the block dimensions are set by the mould design rather than by a cutter.
Applications of Briquette Fuel
Biomass briquettes serve as heating fuel for greenhouses, drying ovens, industrial boilers and household stoves. In many regions they replace coal in small boilers with only minor modification to the grate and the air supply, and the ash can be returned to farmland as a mineral-bearing soil amendment. Because the feedstock is agricultural and forestry residue, briquette production also reduces open burning of straw, cutting air pollution while creating income in rural areas.
Describing a Press in a Specification Document
Four points make a description complete and comparable between suppliers: the pressing principle, whether screw extrusion or piston type; the forming size and output range; the power requirement and whether a three-phase supply is available on site; and feedstock tolerance, including the moisture range, typically 10 to 15 percent, and the acceptable particle size. Add the wear parts that are replaced in service, and the description becomes a document that supports both the purchase decision and the plant planning work that follows it.
Installation and Operating Notes
Mount the press on a level, rigid foundation so that the reaction force of the screw does not tilt the frame.
Provide three-phase power sized to the motor rating, with protection against overload during cold starts.
Feed material at an even rate; flooding the barrel causes torque spikes and uneven briquette length.
Warm the barrel to working temperature before production so that the first blocks form properly.
Keep the screw, mould and heating elements on an inspection schedule, because these are the parts that wear first.
Frequently Asked Questions
Q: What raw materials can a briquette press process?
Crop straw, corn stalks, branches, forage grass, sawdust, shavings and other stem-type biomass with suitable moisture are all common feedstocks.
Q: What size are the briquettes?
Typical screw-press briquettes are 32 by 32 mm in cross-section and 50 to 100 mm long, depending on the mould.
Q: Is heating required during pressing?
Yes. An automatic electric heating device softens surface lignin so the briquette bonds without chemical additives.
Q: What capacity range is available?
Common machines span about 1.0 to 10.0 tonnes per hour, with motor power from 45 to 250 kW across the range.
Q: Do briquettes smoke when burned?
Dry, well-formed briquettes burn with little smoke and a longer burn time than raw biomass, which makes them a practical substitute for firewood or coal.
Q: What moisture should the raw material have?
Keep the feedstock near 10 to 15 percent moisture, using the same drying discipline applied in pellet production.

