Key Points for Operating a Biomass Briquetting Machine Efficiently
A biomass briquetting machine turns loose sawdust, crop residue and other loose biomass into dense rods that burn longer, store better and cost less to transport. The machine itself is mechanically simple, but the results depend heavily on how it is set up and operated. Clarifying the manufacturing process required for the raw material, matching the model to the required output and controlling temperature are the three points that decide whether a briquette line runs profitably.
Clarify the Process Required by the Raw Material
Before the first briquette is pressed, the raw material must be understood. Biomass with high moisture has to be dried, and oversized chips have to be crushed so that the particles are fine enough to interlock under pressure. Materials with very low natural lignin, such as some straw and grasses, may need a small amount of binder or a higher moulding temperature to form a durable rod. The practical sequence is therefore: dry, crush, screen, then briquette. Skipping the preparation stage is the most common reason a machine produces hollow or cracked rods even though the press itself is working correctly.
Match the Model to the Required Capacity
Capacity is not a single number. It changes with the bulk density of the material, its moisture content and the diameter of the mould hole. The rated figures below are given for industrial solid fuel and should be used as a selection guide, with a reserve of about 10 to 20 percent above the required output so the machine is never run at its ceiling.
| Model | Power | Mold hole | Capacity for industrial solid fuel |
|---|---|---|---|
| MKYK-36 | 45 kW | 36 | 0.5 to 1.0 t/h |
| MKYK-48 | 75 kW | 48 | 1.0 to 1.5 t/h |
| MKYK-72 | 110 kW | 72 | 2.0 to 2.5 t/h |
| MKYK-90 | 132 kW | 90 | 2.0 to 2.5 t/h |
| MKYK-120 | 200 kW | 120 | 3.0 to 4.0 t/h |
| MKYK-150 | 250 kW | 150 | 4.0 to 6.0 t/h |
The relationship between holes, power and output is not linear, because a larger mould plate needs more torque to achieve the same pressure per hole. Two models may share a capacity band, as the 72-hole and 90-hole units do above, while differing in power and in the range of materials they handle comfortably.
Control Moulding Temperature
Heat is what makes a briquette hold together without glue. As biomass is forced through the mould, friction raises the temperature of the material and softens the natural lignin, which then re-bonds as the rod cools. Machines with an automatic electronic temperature control system let the operator set and adjust the moulding temperature for each raw material instead of relying on friction alone. Too low a temperature gives a brittle rod with a rough surface, while too high a temperature scorches the outer layer and wastes energy. The working status display makes it possible to watch the trend and correct small deviations before they become a batch of rejects.
Feeding and Labour
Operation is straightforward once the process is fixed. Automation is high, and in normal service only two people are needed for a shift. Material can be loaded manually or fed automatically by conveyor, and the conveyor route is the better choice whenever daily output matters, because it keeps a steady feed rate and removes the variability that manual loading introduces. Feeding should be even: a sudden surge of material raises motor current and can block the mould, while starvation simply wastes the machine time already paid for.
Daily Checks Before Start-Up
Confirm the raw material is dry and crushed to the agreed particle size.
Check that the mould holes are clean and free of hardened material from the previous run.
Verify the working surfaces of the press are lubricated and that moving parts turn freely.
Set the moulding temperature for the material scheduled for that day.
Run the machine briefly without feed, confirm normal sound and current, then start feeding evenly.
Record output, current and temperature so that drift can be spotted over weeks rather than months.
FAQ
Q: What raw materials can be briquetted?
Sawdust, wood shavings, rice husk, peanut shell, straw, grass and similar loose biomass. Materials with low lignin content usually need closer control of temperature or a small amount of binder.
Q: Why are my briquettes cracked or hollow?
Usually because the material is too wet, too coarse, or the moulding temperature is too low. Check the preparation stage before adjusting the press itself.
Q: How many operators are needed?
A typical line runs with about two people per shift when automatic conveyor feeding is used. Manual loading requires more labour and gives a less even feed rate.
Q: How much capacity reserve should be allowed?
Select a model rated 10 to 20 percent above the required output. Output falls when the material is wetter or finer than the test condition, so the reserve protects the daily target.
Q: Is a binder always required?
No. With the right temperature and pressure, many wood based materials bond through their own lignin. Binder is used mainly for low lignin residues or when very high mechanical strength is demanded.
Q: How is moulding temperature adjusted?
With the automatic electronic temperature control system fitted to the machine. Set it per material and adjust in small steps while watching rod surface quality and current draw.

