Knowledge

How to Maintain a Biomass Briquette Machine: Lubrication, Wear Parts and Checks

Why Regular Maintenance Matters on a Briquette Machine

A biomass briquette machine works under high pressure, and its die, rollers and bearings carry heavy loads through every shift. Without regular maintenance, small problems such as a dry bearing or a loose electrical connection turn quickly into expensive repairs and production stoppages. In normal operation no additives, chemicals or foreign bodies are introduced into the briquette: the finished product is a dense natural wood or biomass briquette that does not expand when burning and leaves very low ash. Maintenance keeps this product quality stable while extending the service life of the wearing parts.

Daily and Monthly Lubrication Schedule

The most common cause of premature roller and main bearing failure is lack of oil. The main bearing should be greased every half month, while the bearings of the compression rollers should be oiled every day. Every rotating part needs enough lubricant to run smoothly. Operators should also check the condition of the grease: if the lubricant is dark, gritty or contaminated with dust, it must be flushed out and replaced. Using the grease grade named in the machine manual matters, because high-pressure bearings need a grease that keeps its film strength under load.

Point Interval Note
Main bearing Every half month High-pressure grease, injected until old grease is pushed out
Compression roller bearings Every day Short intervals during continuous production
Grease condition Every refill Replace dark, gritty or dust-contaminated grease
Electrical terminals Monthly Check tightness, contacts and cable insulation

Electrical Cabinet and Wiring Checks

The electrical components in the control cabinet should be checked regularly to confirm that all connections are tight and that the contacts are sensitive and reliable. The cabinet must be protected from moisture and dust and kept clean inside. Loose terminals are a common cause of intermittent faults such as the motor stalling or tripping the overload protection. Cables entering the cabinet should be inspected for cracked insulation, especially near the motor and the main switch.

Inspection and Replacement of Wearing Parts

The wearing condition of each part should be examined according to the machine service condition. Quick-wearing parts, mainly the die, rollers and bearings, should be repaired or replaced before they fail completely. A worn die produces loose briquettes and higher energy consumption, while worn roller shells reduce the pressing force. Keeping spare roller shells and a spare die for the machine reduces downtime. When a new die is installed, check the roller-die gap and the rotation direction according to the manual before starting production.

Die: replace or re-grind when briquettes turn loose and powder output rises.

Roller shells: replace when the pressing surface is scored or the gap can no longer be adjusted.

Bearings: replace at the first sign of play, noise or overheating.

Spare stock: one die, one set of roller shells and one set of bearings per machine.

Reference Models and Maintenance Planning

The table below lists common briquette machine models and their rated parameters, which can be used as a reference when planning maintenance intervals and spare part stock.

Model Power Mold holes Biomass capacity (t/h)
MKYK-36 45 kW 36 1.0-1.5
MKYK-48 75 kW 48 1.5-2.5
MKYK-72 110 kW 72 2.5-3.5
MKYK-90 132 kW 90 3.5-5.0
MKYK-120 200 kW 120 4.0-6.0
MKYK-150 250 kW 150 6.0-10.0

Frequently Asked Questions

Q: How often should the main bearing be greased?
The main bearing of the briquette machine should be greased every half month, while the compression roller bearings should be oiled every day during continuous production.

Q: Why do roller bearings fail quickly?
Most roller bearing failures are caused by lack of oil or by contaminated grease. Keeping the daily lubrication schedule and checking grease condition prevents most of them.

Q: What should be checked in the electrical cabinet?
Check that all terminals are tight, that contacts are clean and reliable, and that the cabinet is dry and dust-free. Loose connections are a common cause of motor faults.

Q: How do I know when the die needs replacing?
When briquettes become loose, output drops, or the machine produces excessive powder, the die holes are usually worn and the die should be re-ground or replaced.

Q: Can the briquette machine run without any additive?
Yes. The briquette is formed by the natural binding of biomass fibers under heat and pressure, so no additives, chemicals or binders are needed in normal operation.

Q: What is the correct roller-to-die gap after a die change?
Set the gap exactly as stated in the machine manual, and confirm the rotation direction before production starts, so the new die is not damaged during the first run.

You Might Also Like

Send Inquiry